Watkins Caldera Spa Vacanza Series Owner's Manual Page 18
- Page / 40
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CONTROL OPERATION
Your control panel consists of an LCD display and convenient touch
pads that allow you to set the water temperature and adjust the skim/
filter cycle settings, lock spa temp, lock entire spa functions, as well as
control the hydrotherapy jets, and lights from spa-side.
LCD DISPLAY
The LCD display on your spa-side control panel continually shows the
spa’s actual water temperature (Home screen). In certain situations, it
will also display other messages. See TROUBLESHOOTING section.
MODE BUTTON
From the Home screen use the MODE ( or ) button to scroll to
the System, Clean, Audio (if your spa is equipped) and Tools screen.
Press the (
+) button
to enter into the sub screens.
TEMPERATURE CONTROL
The set temperature range is from 80°F
(26°C) to 104°F (40°C). Temperatures of any setting may rise slightly depending on the current use and condition of your spa, and on outside
temperature. The factory-set temperature is 100°F (38°C). Whenever power is disconnected and then reconnected to the spa, the water
temperature setting will automatically return to the last temperature entered into the program.
To increase the set temperature, press the (
+)
button, once for each degree of increase temperature desired. If you hold the (
+)
button down,
the set temperature will increase by one degree every half second.
To decrease the set temperature, press the (-) button, once for each degree of decreased temperature desired. If you hold the (-) button down, the set temperature will
decrease by one degree every half second. When the spa water has reached the set temperature, the “READY” icon will display.
JET PUMP CONTROL
Pressing the “JETS” button changes the jet pump functions, depending on the number of presses:
PALATINO, MARINO & VANTO Spa Models only:
1st press: System 1 jet pump runs on low speed
2nd press: System 1 jet pump runs on high speed
3rd press: System 1 & System 2 jet pumps run on high speed
4th press: System 2 jet pump runs on high speed
5th press: Both Systems jet pumps are off
TARINO & AVENTINE
Spa Model only:
1st press: System 1 jet pump runs on low speed
2nd press: System 1 jet pump runs on high speed
3rd press: Jet pump off
• The pump on high speed automatically turns off after operating for one hour. The pump on low speed automatically turns off after operating for one hour.
• When the jets are active, the JETS icon on the control panel will illuminate.
LIGHT ON/OFF & INTENSITY CONTROLS
The light control uses four positions: High, Medium, Low, and Off. To turn on the spa light, press the LIGHT button. This will place all lights in the spa in the High, or
maximum intensity position. When the lights turn on, the light symbol will also illuminate on the control panel display. Press the LIGHT button again to lower the intensity
of the lights to the Medium position. Press the LIGHT button again to lower the intensity even more, placing the lights intensity in the Low position. Press the LIGHT
button one more time to shut the lights off. When the light is deactivated, the light symbol will also turn off.
If the lights are left on, they will automatically be turned off by the control system after 6 hours of continuous operation. The light symbol on the panel will also turn off
when the lights are deactivated.
If the lights will not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on the control panel (see following pages for more information on
SPA LOCK).
15
OPERATING INSTRUCTIONS
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
POWER
POWER
POWER
POWER
POWER
POWER
POWER
READY
F1
F2
POWER
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
POWER
POWER
POWER
POWER
POWER
POWER
POWER
READY
F1
F2
POWER
Light Icon
Filter Cycle Icon
Jets Button
Light Button
Temperature
Down/Off
Temperature
Up /On
Mode
Power Icon
Sleep
Icon
Temp Ready
Icon
Filter Cycle
2 Icon
Filter Cycle 1
Icon
Jet Icon
Mode
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
POWER
POWER
POWER
POWER
POWER
POWER
POWER
READY
F1
F2
POWER
- 2015 OWNER’S MANUAL 1
- Owner’s Manual 2
- TABLE OF CONTENTS 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- RISKS TO AVOID 5
- IMPORTANT SPA INSTRUCTIONS 6
- DECK INSTALLATION 7
- INDOOR/BASEMENT INSTALLATION 7
- SPA LEVELING PREPARATION 7
- SPA COVER INSTALLATION 7
- (TARINO & 8
- ELECTRICAL INSTALLATION 8
- CAUTIONS 10
- SPA FEATURES 12
- JET MENUS 15
- PALATINO 15
- AVENTINE 17
- CONTROL OPERATION 18
- TOOLS MENU 19
- SYSTEM MODE 19
- MANUAL CLEAN CYCLE 19
- LOCK OVERRIDE 20
- SLEEP MODE 20
- FILTER CYCLES 20
- AUDIO MENU (OPTIONAL) 21
- OPERATING INSTRUCTIONS 22
- AIR CONTROL 23
- HYDROTHERAPY JETS 23
- WATERFALL VALVE 23
- DISPLAY INVERSION 23
- WATER TERMINOLOGY 24
- GENERAL INFORMATION 24
- BASIC CHEMICAL SAFETY 25
- BALANCING THE pH 26
- FROG WATER CARE SYSTEM 27
- DO’S AND DON’TS 28
- CHLORINE (SODIUM DICHLOR) 29
- SUPER CHLORINATION 29
- OZONE SYSTEM (OPTIONAL) 30
- WATER QUALITY AND MAINTENANCE 30
- FILTER MAINTENANCE 32
- CARE OF THE SPA PILLOWS 33
- CARE OF THE EXTERIOR 33
- CARE OF THE SPA COVER 33
- ECOTECH SPA CABINET 34
- DRAINING YOUR SPA 34
- NON-OPERATION IN COLD CLIMATE 34
- WINTERIZING YOUR SPA 34
- ACTS INVALIDATING WARRANTY 35
- DISCLAIMERS 35
- WATKINS CUSTOMER SERVICE 35
- TROUBLESHOOTING 36
- READY icon flashes 36
- POWER icon flashes 36
- IMPORTANT 37
- Series 38
- Vista, California 40
- 303765.15 A (12/14) 40
Related products and manuals for Above ground pools Watkins Caldera Spa Vacanza Series
(14 pages)© 2020, manymanuals.com. All rights reserved. | 0.719 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals